Mass properties & composites for things that move fast
I'm a mechanical engineering student at California Baptist University, minoring in aerospace. On CBU Motorsports' Charger 6 electric Formula SAE car I run the mass budget and lead a team of 7 interns building the carbon fiber bodywork, and I lead aerodynamics on our SAE Aero Micro aircraft. I'm looking for internships in aerospace, defense, space, eVTOL and automotive.
Open to Summer 2027 internshipsNew-grad roles from Jan 2028U.S. · Canada · RemoteSAWE Member
Mass Properties Lead · CBU Motorsports (Formula SAE EV) · Jul 2025 – present
The team had no mass properties process, so I built one. Every subsystem now reports mass and location to one live budget, and the whole car works from the same numbers.
23 lbSubteam mass reductions tracked
~0.021 s/kgLap-time sensitivity, OptimumLap
~2%Lap time available from a 50 kg cut
Built the method and the live Excel budget that tracks weight, CG and moment of inertia for every subsystem through PDR, CDR, build freeze and as-built.
Act as the data hub for other subteams: axle loads and sprung/unsprung mass for Suspension, CG vs. center of pressure for Aero, and weight-transfer inputs for Powertrain.
Calculate the car's moments of inertia and use them as inputs for vehicle dynamics calculations.
Keep a component-weight history across Charger 4, 5 and 6, and work with vehicle dynamics and every subsystem to keep CAD mass and placement matched to the real car. Charger 6 gets an as-built weigh-in once it's manufactured.
Ran an OptimumLap sensitivity study to give subteams a reason to cut weight, then tracked 23 lb of reductions across Aero, Chassis, Driver Controls and Composites.
Body & Composites Design Lead · CBU Motorsports · Nov 2024 – present
I design the car's bodywork and take it all the way through manufacturing: surface model, tooling, layup and finish.
Model the body in SolidWorks Surfaces and design the tooling for manufacturability.
Program CAM toolpaths and run a ShopSabre CNC router to cut foam plug molds, then make the parts by wet layup and resin infusion.
Ran coupon tests comparing carbon, Kevlar and fiberglass laminates to guide material selection.
Fixed body-panel fit gaps caused by the as-built chassis differing from CAD by oversizing overlapping panels.
Run cross-subteam coordination meetings with the other subteams the body touches.
Leadership · Succession
Growing a team of 7 composites interns into the team that takes over from me.
Schedule weekly 1:1s with each intern to check progress, answer questions and set their next task.
Run knowledge transfer on design, tooling and layup, so the team can carry the bodywork forward after I leave.
Give interns real projects to own: a composite calculator, a resin-infusion epoxy calculator, and replacing parts on the car with composite components.
Micro Class rewards a light aircraft that carries a lot. I set the aerodynamic configuration and wing design for our 2027 entry; build starts in spring 2027.
47 inWingspan, S1223 airfoil
2.49Max lift coefficient, 3D CFD
14.7L/D at 0° angle of attack
3D wing CFD · lift coefficient vs. angle of attack
Chose the high-lift S1223 airfoil and set the wing at 0° incidence: about 5° angle of attack on the takeoff roll and 0–3° in flight, well clear of the airfoil's sharp 2D stall near 13°.
Oversized the NACA 0018 horizontal tail to handle the S1223's strong pitching moment.
Designed a two-spar wing structure, with hollow carbon tubes for a main spar and a torsion spar running through 3D-printed ribs.
Sized the structure in Ansys Mechanical at about 20 lbf, roughly twice the 10.3 lbf max lift from CFD, and topology-optimized the ribs.
Ran 3D STAR-CCM+ sweeps from 0° to 21° on the full wing. Adding winglets raised max CL from 2.10 to 2.49 and L/D by about 22% at 3–9°, with stall unchanged at 18°. Gurney flap runs are next.
Sized for an estimated 3 lb takeoff weight against a 7 lb maximum.
Body & Composites Design Lead · CBU Motorsports (Formula SAE EV)
The body has to do more than look right: it has to feed air to the battery. I designed a flush NACA duct in the bodywork and checked it in STAR-CCM+ against Powertrain's cooling requirement.
0.07 kg/sAirflow to the battery, STAR-CCM+
0.05 kg/sPowertrain's requirement
+40%Margin over the requirement
Sized and placed a flush NACA duct in the bodywork to draw cooling air into the battery box.
Verified the airflow in STAR-CCM+: 0.07 kg/s against Powertrain's 0.05 kg/s requirement.
STAR-CCM+CFDNACA ductBattery cooling
02
Experience
Jul 2025 – present
Mass Properties Lead
CBU Motorsports, Formula SAE EV
Founded the team's weight, CG and MOI process, run the live mass budget for Charger 6, and supply MOI inputs for vehicle dynamics calculations.
Nov 2024 – present
Body & Composites Design Lead
CBU Motorsports, Formula SAE EV
Bodywork design, tooling and CFRP manufacturing, plus a NACA battery-cooling duct checked in STAR-CCM+. Manage 7 composites interns with weekly 1:1s, knowledge transfer and intern-owned projects so they can take over the role.
Apr 2026 – present
Machine Shop Assistant
California Baptist University
Machine parts on the CNC mill, lathe and router, inspect to spec, and train students and faculty on setup and shop safety.
Jan 2024 – present
Audio-Visual Team Lead
California Baptist University, Conferences & Events
Lead a 12-person crew running large live events, troubleshooting in real time and working between clients and the technical team.
03
Skills
CAD
SolidWorks
SolidWorks Surfaces
Fusion 360
Analysis
STAR-CCM+ (CFD)
SolidWorks FEA
Ansys Mechanical
OptimumLap
Mass properties: weight, CG, MOI
Excel
Manufacturing
CFRP wet layup
Resin infusion
Mold & tooling design
CAM toolpaths
CNC router, lathe, mill
Coupon testing
Other
Team leadership
French (functional)
SAWE member
Let's talk about your next vehicle
I'm looking for internships in mass properties, aerodynamics, composites and manufacturing. Email is the fastest way to reach me.